United Arab Emirates groundwater sample AE-DPS-29
Groundwater analysis for this sample, with English reporting and a WHO drinking-water reference comparison.
Sample evidence summary
AE-DPS-29 documents a groundwater source in Abu Dhabi, United Arab Emirates. The reported source is Customer-supplied water analysis. Use the selected measurements below alongside the complete results table and the source limitations when defining project requirements.
AE-DPS-29 records groundwater results for Abu Dhabi, United Arab Emirates. Source: Customer-supplied water analysis.
- pH: 7.58 (as reported).
- TDS [EC×0.8 calculated]: 7,320 mg/L (as reported).
This summary reproduces selected reported results; it is not a complete drinking-water safety assessment. Dates and reporting limitations are shown below.
- Country
- United Arab Emirates
- Area
- Abu Dhabi
- Water source
- Groundwater
- Sample ID
- AE-DPS-29
- Sampling date / period
- Date needs verification
- Report date
- Date needs verification
- Source
- Customer-supplied water analysis
- Version
- 1
Results and WHO comparison
| Parameter | Reported result | Unit | WHO reference | Comparison |
|---|---|---|---|---|
| pH | 7.58 | — | Context only — no numeric pass/failNo health-based guideline. Optimum operational pH varies with water and materials, usually 6.5–8.5; chlorine disinfection preferably below pH 8. These are process conditions, not raw-water pass/fail limits.Source · PDF page 274 | Context onlyNo health-based guideline. Optimum operational pH varies with water and materials, usually 6.5–8.5; chlorine disinfection preferably below pH 8. These are process conditions, not raw-water pass/fail limits. |
| Conductivity | 9,150 | µS/cm | Context only — no numeric pass/failNo WHO numeric drinking-water guideline used here. It describes ionic conductivity, not drinking-water safety.Source · PDF page 90 | Context onlyNo WHO numeric drinking-water guideline used here. It describes ionic conductivity, not drinking-water safety. |
| TDS [EC×0.8 calculated] | 7,320 | mg/L | Context only — no numeric pass/failNo health-based guideline. WHO describes palatability as generally good below about 600 mg/L and increasingly poor above about 1000 mg/L.Source · PDF page 275 | Palatability not determinedTDS alone cannot establish drinking-water safety. A comparable numeric result is required. |
| Total hardness | 3,230 | mg/L | Context only — no numeric pass/failNo health-based guideline. Assess scaling and treatment requirements for the intended use.Source · PDF page 272 | Context onlyNo health-based guideline. Assess scaling and treatment requirements for the intended use. |
| Appearance | Clear | — | Not configured | Not assessedNo matching reference configured; do not infer that WHO has no guidance. |
SAMPLE AE-DPS-29 · REFERENCE SCREENING
What these results indicate
No result in this record could be conclusively compared against a numeric or microbial reference. Review the units, reporting bases and detection limits listed below each comparison before drawing a conclusion.
Microbial evidence gap: this record has no separately identified E. coli or thermotolerant/faecal coliform result. Total coliforms and general bacterial counts do not replace that test.
Unresolved comparisons: review the reasons beside each result. ND/BLQ without a numeric limit, ambiguous units and unspecified chemical forms are not counted as compliant results.
Treatment options for this sample
No configured treatment trigger could be established from the reported values and units. Confirm the intended use, missing tests and ambiguous units before selecting a process.
Automatically generated screening from this sample record and the cited reference set. This is not an engineer-approved design, a national compliance certificate or a declaration that untreated water is safe to drink.
Source and interpretation
Results describe this sample only and do not establish drinking-water safety. Displayed date is the examination date printed in the source (2025). The report-date column is dated 2026 and is retained separately without correction. The data contributor selected examination dates for publication. TDS was calculated as conductivity multiplied by 0.8, not measured independently.
This is a sample record, not a treatment specification. A process design needs a current, representative source-water analysis and the intended product-water requirements.
WHO drinking-water guidance is used for screening, not certification of untreated source water. TDS categories describe palatability, not overall drinking-water safety. Original dates and laboratory details remain in the source archive.
Download WHO Drinking-water Quality Guidelines (2026 PDF)WHO source document · PDF · approximately 6 MB
FROM WATER ANALYSIS TO PROJECT REQUIREMENTS
Discuss your water quality with our engineering team
Tell us about your source water, required capacity and intended use. Our team can help review the data and define the next engineering steps.