Back to Water Map

United Arab Emirates groundwater sample AE-DPS-07

Groundwater analysis for this sample, with English reporting and a WHO drinking-water reference comparison.

Sample evidence summary

AE-DPS-07 documents a groundwater source in Abu Dhabi, United Arab Emirates. The reported source is Customer-supplied water analysis. Use the selected measurements below alongside the complete results table and the source limitations when defining project requirements.

AE-DPS-07 records groundwater results for Abu Dhabi, United Arab Emirates. Source: Customer-supplied water analysis.

  • pH: 7.45 (as reported).
  • TDS [EC×0.8 calculated]: 6,192 mg/L (as reported).

This summary reproduces selected reported results; it is not a complete drinking-water safety assessment. Dates and reporting limitations are shown below.

Explore water reports from United Arab Emirates

Country
United Arab Emirates
Area
Abu Dhabi
Water source
Groundwater
Sample ID
AE-DPS-07
Sampling date / period
Date needs verification
Report date
Date needs verification
Source
Customer-supplied water analysis
Version
1

Results and WHO comparison

Analysis results for sample AE-DPS-07
ParameterReported resultUnitWHO referenceComparison
pH7.45—Context only — no numeric pass/failNo health-based guideline. Optimum operational pH varies with water and materials, usually 6.5–8.5; chlorine disinfection preferably below pH 8. These are process conditions, not raw-water pass/fail limits.Source · PDF page 274Context onlyNo health-based guideline. Optimum operational pH varies with water and materials, usually 6.5–8.5; chlorine disinfection preferably below pH 8. These are process conditions, not raw-water pass/fail limits.
Conductivity7,740µS/cmContext only — no numeric pass/failNo WHO numeric drinking-water guideline used here. It describes ionic conductivity, not drinking-water safety.Source · PDF page 90Context onlyNo WHO numeric drinking-water guideline used here. It describes ionic conductivity, not drinking-water safety.
TDS [EC×0.8 calculated]6,192mg/LContext only — no numeric pass/failNo health-based guideline. WHO describes palatability as generally good below about 600 mg/L and increasingly poor above about 1000 mg/L.Source · PDF page 275Palatability not determinedTDS alone cannot establish drinking-water safety. A comparable numeric result is required.
Total hardness3,180mg/LContext only — no numeric pass/failNo health-based guideline. Assess scaling and treatment requirements for the intended use.Source · PDF page 272Context onlyNo health-based guideline. Assess scaling and treatment requirements for the intended use.
AppearanceClear—Not configuredNot assessedNo matching reference configured; do not infer that WHO has no guidance.

SAMPLE AE-DPS-07 · REFERENCE SCREENING

What these results indicate

0 above reference / detected0 at or below reference / not detected1 not assessed4 context only

No result in this record could be conclusively compared against a numeric or microbial reference. Review the units, reporting bases and detection limits listed below each comparison before drawing a conclusion.

Microbial evidence gap: this record has no separately identified E. coli or thermotolerant/faecal coliform result. Total coliforms and general bacterial counts do not replace that test.

Unresolved comparisons: review the reasons beside each result. ND/BLQ without a numeric limit, ambiguous units and unspecified chemical forms are not counted as compliant results.

Treatment options for this sample

No configured treatment trigger could be established from the reported values and units. Confirm the intended use, missing tests and ambiguous units before selecting a process.

Automatically generated screening from this sample record and the cited reference set. This is not an engineer-approved design, a national compliance certificate or a declaration that untreated water is safe to drink.

Source and interpretation

Results describe this sample only. They do not represent country-wide conditions or establish drinking-water safety. TDS was calculated from conductivity, not measured independently. Sampling and report dates are reproduced as supplied; some dates require confirmation. The source has an unresolved data or metadata issue; verification is pending.

This is a sample record, not a treatment specification. A process design needs a current, representative source-water analysis and the intended product-water requirements.

WHO drinking-water guidance is used for screening, not certification of untreated source water. TDS categories describe palatability, not overall drinking-water safety. Original dates and laboratory details remain in the source archive.

Download WHO Drinking-water Quality Guidelines (2026 PDF)WHO source document · PDF · approximately 6 MB

FROM WATER ANALYSIS TO PROJECT REQUIREMENTS

Discuss your water quality with our engineering team

Tell us about your source water, required capacity and intended use. Our team can help review the data and define the next engineering steps.

Consult our engineering team
Email Icon Phone Icon WhatsApp Icon Messenger Icon